Product Description :
Duracoat Royale Classic Matt Emulsion is a technically upgraded superior premium quality contains 100% pure acrylic emulsion from the world renowned company Rohm and Haas. It is also manufactured using the best quality emulsion, pigments and extenders to confer a long lasting and aesthetically pleasing finish to any surface it is applied on. It is ideal for use on walls, ceilings, partition boards, plasters and concrete. Virtually odour free and environmental friendly.
Features/Benefits :
- High Classic matt finish
- Easy Application : excellent flow and levelling
- Higher spreading rate
- Higher obliteration
- Hides minor surface defects
- Excellent adhesion
- Rapid drying
- Extremely durable and long lasting
- Virtually odour free
- Vast colour range – Over 1000 shades to choose from
For detailed information please refer to the attached instructions sheet.
- Can be applied by brush, roller or airless spray
- Stir well before use
Use clean water to thin to brushable consistency. DO NOT overthin as this will impair the final properties of the paint film.
Spreading rate :
Spreading rate varies according to the surface porosity and texture. Approximate spreading rates on different surfaces are given below.
| Surfaces | Aprox. Spreading rate in sq.mt/lt |
| Newly Plastered walls | 10 – 14 |
| Previously painted walls in good condition | 15 – 18 |
| Wood float / Cement | 11 – 14 |
| Concrete blocks | 5 – 8 |
| Tyrolene and textured | 3 – 4 |
Shade range :
Available from BS 4800, Royale Colour book and Duracoat Classic Fandeck. Special shades can be made on request.
Pack Sizes :
Available in 1 litre, 4 litres, and 20 litres.
Hints and tips (for best results)
- Always read instructions
- Always use good quality brushes
- Try to paint in one motion
- Always pretest on a small area first
- Ensure good ventilation during application and drying
- Avoid contacts with skin and eyes
- In case of contact with skin wash immediately with plenty of soap and water. In case of contact with eyes, rinse
- mmediately with plenty of water and seek medical advise.
- Wear Dustcoat or Overall, Hand gloves and Breathing mask if spraying.
- Keep out of reach of children and pets.
Instructions
Please read carefully to get optimum performance from this high quality product.
- Stir well till homogeneous after opening.
- Using a little quantity of paint, thin to brushable viscosity and apply onto a small area on the prepared surface to confirm shade and finish. This will avoid redoing the whole work if the shade is not suitable to your taste
Surface preparation : All surfaces should be clean, dry and free from oil, grease and other impurities. Cracks and defects should be filled with suitable crack filler. Powdery or unsound surfaces should be thoroughly cleaned . Then apply one coat of Duracoat Pliolite SurfaceConditioner.
New surfaces : Ensure the surface is dry. Apply one coat of Duracoat Royale All PurposeUndercoat followed by two coats of Duracoat Royale Classic Matt Emulsion.
Previously painted surfaces : Remove all loose, chalky, flaking materials. Powdery materials should be removed with a wire brush. Treat all surfaces with Pliolite Surface Conditioner. Treat surface for mould or algae if present with Duracoat Fungicidal Wash. Allow to dry. Then apply a minimum of two coats of Duracoat Royale Classic Matt Emulsion.
Application : Can be applied by brush, roller or aireless spray. Do Not overthing. Add 15% to 20% of clean water for best results on finish coat.
Spreading capacity : 15 – 18 sq.mt/ltr on smooth previously painted non porous surface. 11 – 14 sq.mt/ltr on cement – wood float.
Drying : Touch dry in 30 minutes, overcoatable within 4 – 5 hours under normal drying conditions.
Stir well before use, clean equipment with water.
If in doubt please contact our Technical department on 823555/954